RTX 8630 User's Guide Page 51
- Page / 117
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
SME VoIP System Guide, Version 1.9
Proprietary and Confidential
Chapter: SME VoIP Administration Interface
51
Parameter
Default values
Description
Multi cell
system
Disabled
Enable this option to allow the Base unit to be set in multi-cell mode
(can be set either as master or slave in the multi-cell chain system –
refer to MAC-units in Chain section for details).
Valid Inputs: Enable, Disable
Must “save and reboot” after change from disabled to enable.
System chain ID
Empty
This is an identifier (in string format e.g. 2275) that is unique for a
specific multi-cell system.
Note: There can be several multi-cell systems in SME network. Up to 7
levels of base stations chains are permitted in a typical setup. Please
refer to accompanied document [2] for further details and description.
Valid Input: 16 bit String length
Synchronization
time (s)
This specifies the period in seconds when elements/nodes (e.g. Base
units) in a specific Multi-cell should synchronise to each other.
Data Sync:
Multicast
To select between multicast or Peer to Peer data synchronisation
mode.
Primary Data
Sync IP
Empty
IP of base station data sync source – the base handling the data
synchronisation.
Using multicast this base IP is selected automatically.
NOTE: Using Peer to Peer mode the IP of the base used for data sync.
source MUST be defined.
NOTE: Using Peer to Peer mode limits the system automatic recovery
feature – as there is no automatic recovery of the data sync. source in
Peer to Peer mode.
Multi cell
debug
None
Enable this feature, if you want the system to catalogue low level multi-
cell debug information or traces.
Options:
Data Sync: Writes header information for all packets received and sent
to be used to debug any special issues. Generates LOTS of SysLog
signaling and is only recommended to enable shortly when debugging.
Auto Tree: Writes states and data related to the Auto Tree
Configuration feature.
Both: Both Data Sync and Auto Tree are enabled.
NOTE: Must only be used for debug purpose and not enabled on a
normal running system
5.12.2 DECT System Settings
Description of DECT Settings for Specific Base units is as follows:
Screenshot
http://ArtTel.ru
- SME VoIP System Guide 1
- Contents 3
- 1 About This Document 6
- 1.1 Audience 6
- 1.3 Important Assumptions 6
- 1.4 What’s Inside This Guide 6
- 1.5 What’s Not in This guide 7
- 1.6 Abbreviations 7
- 1.8 Document History 8
- 1.9 Documentation Feedback 8
- 2.1 Hardware Setup 9
- 2.2.1 RTX Base Stations 10
- 2.3 Wireless Bands 11
- 3.5 Find IP of Base Station 16
- 4 Making Handset Ready 18
- 4.2 Before Using the Phone 19
- 4.3 Using the Handset 20
- 5.1 Web navigation 21
- 5.2 Home/Status 23
- 5.3 Extensions 24
- 5.3.1.1 Extensions list 26
- 5.3.1.2 Edit Extension 27
- 5.4 Servers 33
- 5.5 Network 35
- 5.5.2 VLAN Settings 36
- 5.5.3 DHCP Options 37
- 5.5.4 NAT Settings 37
- 5.5.5 SIP/RTP Settings 38
- 5.8 Time Server 42
- 5.9 Country 44
- 5.10 Security 45
- 5.11.2 LDAP 49
- 5.12.2 DECT System Settings 51
- 5.12.3 Base System Settings 52
- 5.12.4 Base Station Group 53
- 5.12.5 DECT Chain 54
- 5.13 Repeaters 56
- 5.13.1.1 Manually 57
- 5.13.1.2 Local Automatical 57
- 5.13.3 Repeaters list 58
- 5.14 Statistics 59
- 5.14.2 System data 60
- 5.14.3 DECT data 60
- 5.16 Sys log 62
- 5.17 SIP Logs 62
- 6.1 Adding Base stations 63
- 6.1.1 Time Server Setup 64
- 6.1.3 Multi-cell Setup 65
- 6.3.1 Stage 1 70
- 6.3.2 Stage 2 70
- 6.3.3 Stage 3 70
- 6.3.4 Stage 4 70
- 8.1 Network Dimensioning 83
- 8.2 TFTP Configuration 83
- 8.3.1 Base: 85
- 8.3.2 Handsets/Repeaters: 85
- 8.4 Firmware Update Settings 86
- 9 Functionality Overview 90
- 9.1 System Feature List 90
- 9.2 Detail Feature List 91
- Appendix 94
- 10.5 TFTP Server Setup 96
- 10.6 SIP Server Setup 97
- 11.1 Introduction 100
- 11.4 Implementation Cases 102
- 11.5 Base station Setup 103
- 11.6 Configure Time Server 103
- 12.1 Network Requirements 105
- 12.3 Site Planning 105
- 12.4.1 Cell Coverage 106
- 12.5 Network Dimensioning 107
- 14.6 Handover 115
- 14.7 Roaming 116
Related products and manuals for Telephones RTX 8630
Telephones RTX 8630 User Manual
(33 pages)
(33 pages)
© 2020, manymanuals.com. All rights reserved. | 0.635 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals